There is no national cap on how many people can live in a sober living house. Two figures decide it in most homes: a bedroom occupied by one person needs at least 70 square feet of floor area, and a bedroom shared by two or more needs at least 50 square feet per occupant. Shared space, plumbing fixture counts, fire code classification, and fair housing law then decide whether that bedroom arithmetic survives. This guide works through each of those, with the code sections and the published figures, so you can set a defensible number for a specific house and explain it to a building official. Current as of September 2026.
How Many People Typically Live in a Sober Living House?
There is no federal or state law that caps occupancy in a sober living home directly. Most homes run somewhere between 10 and 20 residents, though that range describes what exists rather than what is permitted. The number a particular house can hold comes from four things working at once: the usable floor area of each bedroom, the capacity of the shared spaces and the plumbing, the building and fire code classification the home falls under, and the fair housing rules that stop a city from applying a stricter limit to a recovery residence than it applies to a comparable household. Because a sober living home is residential housing rather than a clinical treatment setting, it is measured against the same standards as any other home on the street.
What Sets the Number
Maximum occupancy is shaped by four inputs working together:
- Building and fire safety requirements
- Housing code space standards
- Disability and fair housing protections
- Recovery housing quality standards, such as NARR or VSL
The U.S. Department of Housing and Urban Development treats two persons per bedroom as a reasonable general standard rather than a ceiling. HUD adopted that position formally in December 1998, publishing the March 20, 1991 memorandum from its General Counsel as agency policy at 63 Federal Register 70256. The notice states that the Department believes an occupancy policy of two persons in a bedroom is, as a general rule, reasonable under the Fair Housing Act, and then says plainly that the reasonableness of any occupancy policy is rebuttable. Bedroom size, the size and configuration of the unit, and the capacity of the septic, sewer, or other building systems can each justify a different number in either direction. Two persons per bedroom is also the working standard in several states, including under Maine’s new recovery residence law.
Code Maximum vs. Program Maximum
A home might technically fit more people under local code than it should actually house. Recovery housing quality standards emphasize dignity, personal space, and a home-like environment, so the program maximum is often set slightly below the absolute code maximum. Protecting comfort and community culture usually pays off in longer stays and stronger outcomes, which is part of why larger sober living homes can work well when they are staffed and configured for the resident count.
How to Estimate Bed Capacity From Total Square Footage
VSL Capacity Modeling Insight (2025 Research)
In 2025, VSL analyzed a national sample of recovery housing to understand how overall building size correlates with real-world bed capacity. Using a linear regression model, we built a practical way to estimate a home’s capacity from total square footage. This model powers VSL’s Sober Living Calculator.
Rather than a flat “square feet per person” rule, the model reflects how homes behave as they grow:
- Each additional bed requires progressively more space, accounting for egress, circulation, bathroom demand, and livability, not just bedroom size.
- Larger homes become less space-efficient per bed, so you cannot add residents at a linear rate without eroding safety, comfort, or compliance.
- Known, permitted bed counts take priority, and the model only estimates from square footage when those numbers are not yet established.
In plain terms, total building size sets an upper boundary, but each additional bed costs more square footage than the last. That is why responsible occupancy naturally tapers as a home scales.
What Actually Controls Occupancy in a Sober House?
Communities sometimes assume sober living homes operate under a separate rulebook. They do not. Occupancy is governed by four overlapping layers that apply to all residential housing, and each layer answers a different question about the same house.
| Regulatory layer | What it sets | What it means for your headcount |
|---|---|---|
| Local building code and occupancy classification | Whether the home is treated as a one- or two-family dwelling, a lodging or rooming house, or another residential group use | The classification drives egress and, at some resident counts, fire suppression. A lodging-house classification is the one that most often forces an expensive retrofit, so confirm it before you buy or lease. |
| Fire and life safety code | The number and location of exits, smoke and carbon monoxide detection, and whether sprinklers are required at your resident count | Fire officials rarely negotiate. If the code triggers sprinklers above a certain number of residents, that number is a hard wall until the system is installed. |
| Housing and property maintenance code | Minimum floor area per occupant, what counts as a legal bedroom, plumbing fixture counts, and minimum sizes for kitchens and living rooms | This is where the arithmetic happens. Section 404.4.1 of the International Property Maintenance Code sets 70 square feet for a bedroom occupied by one person and 50 square feet per occupant for a bedroom occupied by more than one. |
| Fair Housing Act and disability rights | The ceiling a municipality is allowed to place on your home relative to comparable households | It does not raise your code limit. It stops a city from applying a lower limit to a recovery residence than it applies to any other household of the same size in the same district. |
These four layers do not add together. They compete, and the lowest number among them is your maximum. The arithmetic itself sits in the housing code: section 404.4.1 of the International Property Maintenance Code requires that every bedroom occupied by one person contain at least 70 square feet, and every bedroom occupied by more than one person contain at least 50 square feet of floor area for each occupant. In practice the binding constraint is rarely the one operators expect: plenty of homes have bedrooms that would hold sixteen people and plumbing or septic capacity that will only support ten.
Fair housing law is a shield, not a lever. It can stop a city from singling out your home for a stricter cap, and it cannot give you more residents than the building code, the fire code, and the plumbing allow. Operators who lead with the Fair Housing Act before doing the code arithmetic tend to lose both arguments.
Room Size, Bedroom Rules, and How Many Beds Fit
Translating code into beds starts with room size. Most states rely on versions of the IRC vs. IBC framework, and the International Residential Code is the one that usually governs a home-scale recovery residence.
Minimum Bedroom Requirements
The International Residential Code governs a home-scale recovery residence in most states, and it sets three requirements that decide whether a room is a bedroom at all:
- Floor area: not less than 70 square feet (IRC R304.1)
- Horizontal dimension: not less than 7 feet in any direction (IRC R304.2)
- Emergency escape: at least one operable emergency escape and rescue opening, with a net clear opening of not less than 5.7 square feet, a net clear height of at least 24 inches, and a net clear width of at least 20 inches (IRC R310)
Bathrooms, living rooms, and kitchens then have to serve the number of residents the bedrooms allow, and the whole set of space requirements works together rather than bedroom by bedroom.
How Many Beds Fit in a Bedroom? Floor Area by Occupant Count
Count usable floor area, not the number on the listing. Closets, sloped ceilings below the code minimum height, and unusable corners do not count toward the figure. Two further tests come from the International Residential Code, which requires a habitable room to be not less than 70 square feet in area and not less than 7 feet in any horizontal dimension (IRC R304.1 and R304.2), and every sleeping room to carry a compliant emergency escape and rescue opening (IRC R310). Shared rooms are normal in recovery housing, and bunk beds for recovery can raise capacity without crowding as long as egress and floor area still comply. Confirm the numbers below with your local building department, because states adopt code editions on their own schedules.
| Usable bedroom floor area | Maximum occupants | What the rule means |
|---|---|---|
| Under 70 sq. ft. | Not a legal bedroom | IRC R304.1 sets 70 square feet as the minimum area for any habitable room, so the space is not a bedroom regardless of how a listing describes it. |
| 70 to 99 sq. ft. | 1 | The one-occupant minimum in IPMC 404.4.1. A room in this band is a single room and stays one unless a wall moves. |
| 100 to 149 sq. ft. | 2 | Two occupants at 50 square feet each. Most bedrooms in a converted single-family house land in this band. |
| 150 to 199 sq. ft. | 3 | Three occupants at 50 square feet each. Floor area complies, and egress capacity becomes the next question the code asks. |
| 200 to 249 sq. ft. | 4 | Four occupants at 50 square feet each, which in practice means a former primary bedroom or a bonus room. |
| 250 sq. ft. and above | 5 or more | Floor area is no longer the binding rule. The limit moves to egress, plumbing fixture counts, and common-area minimums. |
Read the bands as a ceiling on each room rather than a plan for it. A room that clears the area test can still fail on egress or on storage, and both of those are cheaper to discover with a tape measure than with a departing resident.
A widely repeated version of this rule adds 50 square feet to the 70 square foot minimum and arrives at 120 square feet for two occupants. That is not what the code says. Section 404.4.1 of the International Property Maintenance Code requires 70 square feet for a bedroom occupied by one person and 50 square feet per occupant for a bedroom occupied by more than one, so two occupants need 100 square feet, not 120. The 50 square foot figure replaces the 70; it does not stack on top of it. NARR Standard 3.0 section 2.E.14.d uses the same 50 square feet per bed.
What Never Counts as a Bedroom
Many homes include bonus rooms that cannot legally be used for sleeping:
- Finished attics without proper ceiling height or egress
- Basements without compliant emergency exits
- Pass-through rooms, dens, or living rooms without required privacy
- Any room without a proper means of escape
How Shared Space and Plumbing Cap the Total
Even large bedrooms cannot push occupancy past what the shared spaces support, and on most homes this is the constraint that actually binds. Bathrooms, kitchens, and living areas have to sustain daily life and a safe evacuation for everyone in the house. NARR Standard 3.0 sets the fixture ratio at section 2.E.14.e and the per-bed floor area at section 2.E.14.d, and the property maintenance code sets the common-area minimums. The published figures are specific.
| Shared space | Published minimum | What it means for your headcount |
|---|---|---|
| Sinks, toilets, showers | One of each per six residents, under NARR Standard 3.0 § 2.E.14.e | The ratio that most often caps a house below its bedroom count. A ten-bed home needs two of each as a floor, and a twelve-bed home needs two plus real morning capacity. |
| Living room | 150 sq. ft. at six or more occupants, under IPMC Table 404.5 | A code-compliant living room can still be too small to seat the house. That is a retention problem rather than a compliance one, and it shows up in length of stay. |
| Dining room | 100 sq. ft. at six or more occupants, under IPMC Table 404.5 | The requirement starts at six occupants, so it frequently becomes relevant at exactly the point an operator wants to add another bed. |
| Kitchen | 60 sq. ft. at six or more occupants, under IPMC Table 404.5 | The floor-area figure is a minimum rather than a target. Counter space and the number of people who can cook at once decide whether the kitchen works at your count. |
| Food storage | Storage space for every resident, with no quantity specified, under NARR Standard 3.0 § 2.E.14.g | No published standard sets a refrigerator ratio for recovery housing. A figure quoted to you as a NARR requirement is not one, so treat any ratio you adopt as house policy. |
| Hot water, heating, septic or sewer | No published per-resident figure | HUD names septic, sewer, and other building system capacity as a legitimate physical limitation on occupancy, which makes a system limit a defensible basis for a lower number. |
Then check the systems the code table does not cover: hot water recovery, HVAC capacity, and septic or sewer limits. HUD’s own occupancy notice names septic and sewer capacity as a legitimate reason to set a lower number, so a system limit is a defensible basis for a cap rather than a soft preference.
Physical Bed Capacity vs. Practical Operating Capacity
Every check above produces its own number, and the house holds whichever is lowest. A sober living home with floor area for ten beds but compliant escape openings in rooms for only six is a six-bed home, however the listing reads.
- Physical capacity: The bed count that raw floor area allows before egress, fixtures, and shared space are applied.
- Practical capacity: The bed count the house can sustain once every bedroom has a compliant escape opening and the bathrooms, kitchen, and living areas meet the per-resident figures above.
- The gap between them: Where projections go wrong, because income gets modeled on the physical number while the home can only run at the practical one.
Two details tend to shrink the practical number. Live-in staff, including a resident house mentor, count as residents under the NARR fixture ratio, so a ten-bed home with a live-in mentor plans fixtures for eleven. Adding residents can also push a home across an occupancy threshold that brings added fire alarm or sprinkler requirements, which turns one more bed into a capital project.
Running a few beds below the practical maximum often earns more than filling every one. Crowding strains the house mentor and the neighbors, shortens resident stays, and can put certification at risk where NARR standards apply, which is why underwriting a sober living property starts from verified capacity rather than the room count.
Fair Housing, Disability Rights, and the “Two Per Bedroom” Rule
Because sober living homes serve people with disabilities, they carry federal protections that shape how occupancy limits can be applied. Understanding these protections helps operators avoid accidental discrimination and helps cities stay on solid legal ground.
What HUD Actually Says About Occupancy
HUD’s two persons per bedroom guidance is frequently misread as a hard ceiling. The 1998 statement of policy at 63 Federal Register 70256 says the opposite:
- Two persons per bedroom is a general rule that HUD considers reasonable, and its reasonableness is expressly rebuttable.
- Bedroom size, the size and configuration of the unit, and the presence of dens or studies all bear on whether a different number is reasonable.
- A stricter limit may be unreasonable where it does not reflect a real health or safety concern.
- A more generous limit may be reasonable where bedrooms are large, or where state and local codes allow it.
- The capacity of the septic, sewer, or other building systems is a legitimate physical limitation that can support a lower number.
- The guidance tests whether an occupancy policy unlawfully excludes families with children, so it is familial-status guidance rather than a bed count for a sober living home.
Can a City Cap How Many Unrelated People Live in a Sober Home?
Sometimes, but it cannot do so under the Fair Housing Act’s occupancy exemption. A municipality may define “family” to include a set number of unrelated adults, and the 2016 joint statement from the Department of Justice and the Department of Housing and Urban Development says such a definition does not violate the Act on its face. What the city cannot do is shelter that cap behind the Act’s exemption for maximum occupancy restrictions. In City of Edmonds v. Oxford House, Inc., 514 U.S. 725 (1995), the Supreme Court held that a family-composition rule describes who may compose a household rather than the maximum number of occupants a dwelling may house, so 42 U.S.C. § 3607(b)(1) does not immunize it and the Fair Housing Act still applies.
- Discriminatory intent. The cap, or its enforcement against this home, was adopted or applied because the residents are people in recovery.
- Discriminatory effect. A facially neutral cap has an unjustified disparate effect on people with disabilities, which the 2016 joint statement identifies as an independent basis for liability.
- Refusal of a reasonable accommodation. The city declined a modification of the cap that was necessary to give people with disabilities an equal opportunity to use and enjoy housing.
A city may cap unrelated adults inside its definition of family. It may not defend that cap with the Fair Housing Act’s maximum occupancy exemption, because City of Edmonds v. Oxford House, Inc. placed family-composition rules outside that exemption. The operator’s working remedy is a reasonable accommodation request, and it only exists once it has actually been made in writing.
Make the request in writing, to the office that issued the limit, and keep the code arithmetic attached to it. An accommodation request that arrives with measurements reads as a compliance question; one that arrives without them reads as a complaint.
Maximum Occupancy Caps vs. Family Definitions
The Fair Housing Act leaves room for reasonable local, state, or federal limits on how many people may occupy a dwelling (42 U.S.C. § 3607(b)(1)). Whether a local rule falls inside that exemption depends on what it actually regulates.
| Question | Maximum Occupancy Cap | Family-Composition Rule |
|---|---|---|
| What it limits | Total occupants per dwelling | Who counts as a household, usually by capping unrelated adults |
| What it is based on | Floor area or number of sleeping rooms | The relationship among the occupants |
| Who it applies to | Every household equally | Unrelated groups, not related families |
| Fair Housing Act status | Exempt when reasonable | Not exempt, so intent, effect, and accommodation rules apply |
Equal treatment is the line the 2016 joint statement draws. A city that lets five unrelated adults live together as a family but requires a special permit for five residents in recovery is treating the sober house less favorably, which the statement calls unlawful. A cap on groups larger than the family definition can stand on its face, but the city still has to consider an accommodation to exceed it.
Spacing and Dispersal Rules Between Group Homes
Some cities require a minimum distance between group homes. The 2016 joint statement treats a spacing requirement placed on a home that fits within the ordinary family definition as an unlawful condition not imposed on other households, while allowing that concentration concerns may be weighed when a home asks to exceed the cap. Courts have analyzed these rules in different ways, so treat a spacing ordinance as a question for local counsel rather than a settled answer.
Keep reading The Federal Fair Housing Act and Sober Living: Everything You Need to Know How disability protections apply to recovery housing, and where they stop. →When to Request a Reasonable Accommodation
Request an accommodation when a local limit rests on an unrelated-persons definition, when a city applies a lower cap to sober living than to comparable homes, or when a neutral code requirement needs a modest modification to avoid a discriminatory result. VSL’s guide to requesting reasonable accommodation covers what the request has to contain and who at the municipality has to receive it.
- ✓How a recovery residence gets classified
- ✓Where Fair Housing protection actually applies
- ✓What a reasonable accommodation request looks like
How to Set Your Home’s Occupancy Number in Seven Steps
Setting occupancy is a measurement exercise with a legal check at the end, and it runs in the same order every time. The seven steps below are the shape of the work. The full measurement walkthrough, including what counts as usable floor area and the documentation packet a building official asks for, is covered step by step on the occupancy determination guide.
- Get a to-scale floor plan. Include every bedroom, hallway, stairway, exit, bathroom, kitchen, and living space, with dimensions labeled and egress windows marked. A laser measure or a phone scanning app is enough; VSL’s walkthrough on scanning a floor plan with CubiCasa covers the tooling.
- Measure usable floor area, not room size. Closets, sloped ceilings below the code minimum height, and unusable corners come out of the total. Confirm each bedroom is at least 7 feet in every horizontal direction and carries a compliant emergency escape opening, because a room that fails either test holds zero residents regardless of its area.
- Run the bedroom arithmetic. 70 square feet for a single occupant, 50 square feet per occupant for any room holding two or more. Add the rooms together for a bedroom-driven maximum.
- Gate the total on shared space and systems. Apply the fixture and common-area minimums above, then check hot water recovery, HVAC, and septic or sewer capacity. This produces a second, usually lower, maximum.
- Take the lower of the two numbers. The bedroom count is a ceiling, not a target, and the shared-space count almost always wins on a house that was built for a single family.
- Run a fair housing reasonableness check. Write down why the number is what it is, in code terms, and confirm you are not applying a stricter standard to residents in recovery than the same house would face with any other occupants. That written rationale is the document a reasonable accommodation request is built on, and it is also what defuses a hostile planning-board meeting.
- Apply the livability test before you finalize. Is there seating for everyone at once? Does the morning bathroom rotation work? Is there real storage for each resident’s belongings? A house that clears code and fails this loses residents, which is why program maximums are frequently set one or two beds below the code maximum.
Calculate two maximums and publish the lower one. The bedrooms give you one number and the bathrooms, kitchen, living space, and septic capacity give you another. The lower number is the occupancy of the house, and writing down which constraint produced it is what makes the figure defensible.
Most operators can complete the measurement in an afternoon. What takes longer is the judgment about where to set the program maximum relative to the code maximum, and that is the decision worth talking through with someone who has done it on more than one house.
Support for every stage
Pick the level of support that fits where you are.
Just getting startedSee how the sober living opportunity works and what starting with VSL looks like. LaunchpadGuided pre-launch program: one-on-one strategy, Academy training, weekly coaching, and templates. MasteryHands-on startup, certification, and operating support inside the Chartered Operator community.Questions first? Call (844) 762-3747, weekdays 8a to 5p.
National quality standards from the National Alliance for Recovery Residences reinforce this order of operations, and the NARR levels of care help match a resident count to the level of support a home actually provides. A Level I home with no on-site staff supports a different headcount than a Level III home with daily programming, even in an identical building.
Keep reading How to Determine Maximum Occupancy in a Recovery Home: A Step-by-Step Guide The measurement walkthrough: usable floor area, the shared-space gate, and the documentation an inspector expects. →Common Pitfalls and Red Flags in Sober House Occupancy
Occupancy problems tend to fall into predictable patterns. Watching for them protects both residents and the home’s standing with the community.
Operator Pitfalls
- Overcrowding: Adding beds to chase revenue undermines safety and community culture.
- Improper bedrooms: Using rooms without proper egress creates real safety risk.
- No documentation: Without a written rationale, occupancy decisions can look arbitrary.
Municipal Pitfalls
- Discriminatory caps. Setting a lower resident limit for sober homes than for comparable households in the same district is the clearest fair housing exposure a municipality has.
- Leaning on the family definition. An unrelated-persons cap is not automatically unlawful, but it is not shielded by the Fair Housing Act’s occupancy exemption either, so a city that treats it as a safe harbor is mistaken.
- Ignoring accommodation requests. Cities have to review reasonable accommodation requests in good faith and on the record, and a non-answer is treated as a denial.
Signs Something Is Wrong
- Residents must cross another bedroom to exit
- Egress windows are painted shut
- Bathrooms are severely over capacity
- Common areas cannot support the number of people living in the home
Getting Occupancy Right With Operators and Local Officials
The best occupancy outcomes come from collaboration. Operators, developers, municipal officials, and neighbors all benefit when the conversation centers on safety, quality, and rights rather than fear or stigma.
How Operators Build Trust
A well-prepared occupancy plan gives officials and neighbors something concrete to work with. Strong plans include:
- Measurements and floor plans
- Applicable code references
- A clear rationale for room assignments
- Fire safety considerations
- A fairness check showing nondiscriminatory treatment
Sharing this information openly, and offering to walk the home together, tends to build real confidence with local officials.
What Municipal Officials Can Do
Cities support safe, successful recovery housing when they:
- Apply the same health and safety rules used for comparable homes
- Use fair housing compliant approaches to occupancy
- Request reasonable documentation instead of imposing special restrictions
Working together reduces conflict and helps residents focus on rebuilding their lives in a stable home.
Frequently Asked Questions About Sober Living Occupancy
How many people per room in a sober living house?
Two per bedroom is the working answer in most homes, and floor area decides it. A bedroom occupied by one person needs at least 70 square feet, and a shared bedroom needs at least 50 square feet per occupant under IPMC 404.4.1, so 100 square feet supports two beds.
Is there a maximum number of people who can live in a sober living house?
Yes, but it is set locally rather than nationally. No federal or state law caps sober living occupancy directly. The limit comes from bedroom floor area, plumbing fixture counts, the fire code classification, and system capacity, and the lowest of those numbers is the maximum.
Can a city limit how many unrelated people live in a sober living home?
A city may define family to include a set number of unrelated adults, and that definition is not unlawful on its face. It cannot claim the Fair Housing Act maximum occupancy exemption for it, because City of Edmonds v. Oxford House placed family-composition rules outside that exemption.
How many bathrooms does a sober living home need?
One sink, one toilet, and one shower per six residents, under NARR Standard 3.0 section 2.E.14.e. Local plumbing codes sometimes require more. A twelve-bed home therefore needs two full bathrooms as a floor, and most operators add a half bath to make the morning rotation workable.
Does the Fair Housing Act let a sober living home exceed the local occupancy limit?
No. The Fair Housing Act stops a city from applying a stricter limit to a recovery residence than to a comparable household, and it does not raise the limit that the building code, the fire code, and the plumbing set. Where a neutral rule blocks equal housing opportunity, the remedy is a reasonable accommodation request.
Educational only; not legal advice. Code editions, adopted amendments, and local ordinances vary by jurisdiction and change. Figures reflect conditions as of September 2026. Confirm current requirements with your building and fire officials and consult a qualified attorney on fair housing questions.
Setting Occupancy the Right Way
Occupancy in a sober living house is a measurement question first and a civil rights question second, and getting the order right is most of the work. Measure the bedrooms, gate the total on the plumbing and the shared space, take the lower number, and write down which constraint produced it. That single document is what satisfies a building official, supports a certification application, and gives an operator something concrete to bring to a neighbor or a planning board. It also protects the home financially, because an occupancy figure set by arithmetic survives scrutiny in a way that one set by ambition does not.
If you are planning, operating, or evaluating a sober living home and want a second set of eyes on the number, reach out to the VSL team and we will work through the plan with you.
Research and Sources
- City of Edmonds v. Oxford House, Inc., 514 U.S. 725 (1995). https://tile.loc.gov/storage-services/service/ll/usrep/usrep514/usrep514725/usrep514725.pdf
- International Code Council. (2021). International Property Maintenance Code §§ 404.4.1, 404.5, Table 404.5 (as adopted by New York State). https://www.elmsford.gov/DocumentCenter/View/234/Occupancy-Design-References-PDF
- International Code Council. (2021). International Residential Code §§ R304.1, R304.2, R310 (adopted excerpt, Grant County, Washington). https://www.grantcountywa.gov/DocumentCenter/View/9481/2021-Residential-Excerpts
- National Alliance for Recovery Residences. (2018). NARR standard 3.0 §§ 2.E.14.d, 2.E.14.e, 2.E.14.g. https://narronline.org/wp-content/uploads/2024/05/NARR-Standard-3.0.pdf
- U.S. Department of Housing and Urban Development. (1998, December 18). Fair housing enforcement: Occupancy standards; notice of statement of policy. 63 Federal Register 70256. https://www.govinfo.gov/content/pkg/FR-1998-12-18/html/98-33568.htm
- U.S. Department of Justice & U.S. Department of Housing and Urban Development. (2016, November 10). Joint statement on state and local land use laws and practices and the application of the Fair Housing Act. https://www.justice.gov/opa/file/912366/download
- Cornell Legal Information Institute. (n.d.). 42 U.S.C. § 3607: Religious organization or private club exemption. https://www.law.cornell.edu/uscode/text/42/3607
